Jump to main content

Dorico 4.3.0

Plug-in Reference

Table of Contents
Included VST Audio Effect Plug-ins

Included VST Audio Effect Plug-ins
- AmpSimulator
  AmpSimulator is a distortion effect that emulates the sound of various types of guitar amp and speaker cabinet combinations. A wide selection of amp and cabinet models is available.
- AutoPan
  This auto-pan effect provides several parameters to modulate the left/right stereo position. You can use presets or create individual curves for the modulation waveform. AutoPan also allows for chopping effects by linking the modulation of left and right channel.
- Brickwall Limiter
  Brickwall Limiter ensures that the output level never exceeds a set limit.
- Chorus
  This plug-in is a single-stage chorus effect. It doubles the audio that is sent into it with a slightly detuned version.
- Compressor
  Compressor reduces the dynamic range of the audio, making softer sounds louder or louder sounds softer, or both.
- Distortion
  Distortion adds crunch to your tracks.
- DJ-EQ
  DJ-EQ is an easy-to-use 3-band parametric equalizer that resembles the EQs found on typical DJ mixers. This plug-in is designed for quick sound fixes.
- DualFilter
  DualFilter filters out specific frequencies while allowing others to pass through.
- EnvelopeShaper
  EnvelopeShaper can be used to attenuate or boost the gain of the attack and release phase of audio material.
- Flanger
  This is a classic flanger effect with added stereo enhancement.
- Frequency 2
  Frequency 2 is a high-quality equalizer with 8 fully parametric bands. The bands can act as shelving filter, as peak or notch filter (band-pass), or as cut filter (low-pass/high-pass).
- Gate
  Gating, or noise gating, silences audio signals below a set threshold. As soon as the signal level exceeds the threshold, the gate opens to let the signal through.
- Limiter
  Limiter is designed to ensure that the output level never exceeds a set output level, to avoid clipping in following devices.
- Lin One Dither
  Lin One Dither is a dithering plug-in that uses advanced algorithms and offers additional noise shaping to increase the apparent signal-to-noise ratio by altering the spectrum of the low-level audio signal.
- Maximizer
  Maximizer raises the loudness of audio material without the risk of clipping. The plug-in provides two modes, Classic and Modern, that offer different algorithms and parameters.
- MonoDelay
  This is a mono delay effect. The delay line uses tempo-based or freely specified delay time settings.
- MonoToStereo
  MonoToStereo turns a mono signal into a pseudo-stereo signal. The plug-in can be used on mono audio or on stereo audio with equal channels.
- MorphFilter
  MorphFilter lets you mix low-pass, high-pass, band-pass, and band-reduction filter effects, allowing for creative morphings or mixtures between two filters.
- MultibandCompressor
  MultibandCompressor allows a signal to be split into four frequency bands. You can specify the level, bandwidth, and compressor characteristics for each band.
- Octaver
  This plug-in can generate two additional voices that track the pitch of the input signal one octave and two octaves below the original pitch. Octaver is best used with monophonic signals.
- Phaser
  Phaser produces the well-known swooshing phasing effect with additional stereo enhancement.
- PingPongDelay
  This is a stereo delay effect that alternates each delay repeat between the left and right channels. The delay line uses tempo-based or freely specified delay time settings.
- REVerence
  REVerence is a convolution tool that allows you to apply room characteristics (reverb) to the audio.
- RoomWorks SE
  RoomWorks SE is a smaller version of the RoomWorks plug-in. RoomWorks SE delivers high quality reverberation, but has fewer parameters and is less CPU demanding than the full version.
- Rotary
  This modulation effect simulates the classic effect of a rotating speaker.
- StereoEnhancer
  StereoEnhancer expands the stereo width of stereo audio material. It cannot be used with mono audio.
- SuperVision
  SuperVision is a professional tool suite for monitoring and analyzing your audio. The plug-in comes with several different modules for level, spectral, phase, or waveform analysis. Up to nine module slots allow you to create custom layouts for better overview.
- ToneBooster
  ToneBooster is a filter that allows you to raise the gain in a selected frequency range. It is particularly useful if it is inserted before AmpSimulator in the plug-in chain, greatly enhancing the tonal varieties available.
- Tremolo
  Tremolo produces amplitude modulation.
- Tube Compressor
  This versatile compressor with integrated tube-simulation allows you to achieve smooth and warm compression effects. The VU meter shows the amount of gain reduction. Tube Compressor features an internal side-chain section that lets you filter the trigger signal.
- Vibrato
  Vibrato creates pitch modulation.
- VintageCompressor
  VintageCompressor is modeled after vintage type compressors.
- VST Amp Rack
  VST Amp Rack is a powerful guitar amp simulator. It offers a choice of amplifiers and speaker cabinets that can be combined with stomp box effects.
- VST Bass Amp
  VST Bass Amp is a bass amp simulator. It offers a choice of amplifiers and speaker cabinets that can be combined with stomp box effects.
- VSTDynamics
  VSTDynamics is an advanced dynamics processor. It combines three separate effects: Gate, Compressor, and Limiter, covering a variety of dynamic processing functions.
- WahWah
  WahWah is a variable slope band-pass filter that can be auto-controlled via MIDI modeling the well-known analog pedal effect.

Included VST Audio Effect Plug-ins

AmpSimulator

Dorico 4.3.0

Forum Support

About Privacy Policy Terms & Conditions Team